Understanding the BL-ST-031 and 锐腾/GS Compatibility
The BH-Sens BL-ST-031 is a pre-programmed 433MHz TPMS sensor manufactured by Baolong Technology (BH-Sens brand). It is designed as a direct OE replacement for vehicles using original sensors with part numbers 10290600, 10625492, 10718213, and 11205327. For 锐腾/GS (MG GS / Roewe RX5 / Rising ER6 series), this sensor covers approximately 59 specific OE fitments.
This is a clamp-in type sensor, meaning it uses a metal valve stem that screws into the wheel rim. It ships pre-programmed with the correct ID and frequency for most compatible models, so no additional programming tool is required for basic function—though a TPMS relearn procedure may be necessary after installation.
Which 锐腾/GS Models and Years Are Covered?
The BL-ST-031 sensor fits the following vehicle platforms within the 锐腾/GS family:
| Vehicle Line | Model Variant | Approximate Year Coverage | Notes |
|---|---|---|---|
| 锐腾 (MG GS) | 1.5T / 2.0T | 2015–2020 | Pre-facelift and facelift models |
| 锐腾 (MG GS) | Plug-in Hybrid | 2017–2020 | Verify frequency; some PHEV variants use 433MHz |
| Roewe RX5 | All trims | 2016–2021 | Same platform as 锐腾/GS |
| Roewe RX5 MAX | All trims | 2019–2022 | Check wheel type; clamp-in compatible |
| Rising ER6 | All trims | 2020–2022 | Electric variant; 433MHz confirmed |
| MG ZS | All trims | 2017–2020 | Some late models; verify OE number |
Important: Year ranges are approximate. Always confirm using your vehicle’s VIN or the original sensor part number. Not all 锐腾/GS models built in a given year use the same sensor.
How to Verify Fitment Before Buying
Follow these four steps to ensure the BL-ST-031 fits your specific vehicle:
Step 1: Locate Your Current Sensor’s OE Number
Remove one wheel and inspect the TPMS sensor mounted on the valve stem. The OE number is printed on the sensor body, usually near the battery or on the side. Common numbers for this family include:
- 10290600
- 10625492
- 10718213
- 11205327
If your sensor shows any of these numbers, the BL-ST-031 is a direct replacement.
Step 2: Check the Frequency
The BL-ST-031 operates on 433MHz. Most 锐腾/GS models use 433MHz, but some early units (pre-2012) may use 315MHz. To verify:
- Look for a frequency label on your current sensor.
- Check your owner’s manual or service booklet for TPMS specifications.
- Use a TPMS scan tool to read the sensor ID and frequency.
Step 3: Confirm Wheel Type and Valve Stem
The BL-ST-031 is a clamp-in sensor with a metal valve stem. It fits standard steel and alloy wheels that accept a clamp-in valve. If your vehicle uses rubber snap-in sensors (common on some older models), the BL-ST-031 will not fit without changing the valve hole design.
Step 4: Cross-Reference with the Vehicle VIN
Provide your VIN to the Risen Auto support team or use the online fitment checker. The BL-ST-031 is listed as compatible with 59 specific OE fitments—your VIN must match one of those entries to guarantee fitment.
Installation and Relearn Tips
The BL-ST-031 is pre-programmed, so it will broadcast the correct sensor ID and frequency to your vehicle’s TPMS receiver. However, after installation, the system may require a TPMS relearn procedure. This can be done in one of three ways:
- Automatic relearn – Some 锐腾/GS models will recognize new sensors after driving above 25 mph (40 km/h) for 10–15 minutes.
- Manual relearn via TPMS tool – Use a standard TPMS trigger tool to wake each sensor in sequence (LF, RF, RR, LR).
- Dealer scan tool – Some models require a diagnostic tool to register new sensor IDs.
Always check your vehicle’s service manual for the exact relearn procedure. Incorrect sequence can cause the TPMS warning light to stay on.
Recommended Part
For most 锐腾/GS models (2015–2020), MG ZS, Roewe RX5, and Rising ER6, the BL-ST-031 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Im, MG, Rising, Roewe | OE# 10290600, 10625492, 10718213 is a reliable, cost-effective replacement. It matches the OE specifications of Baolong sensors and is sourced directly from China, ensuring competitive pricing without sacrificing compatibility.
FAQ
Will the BL-ST-031 work on my 2013 锐腾/GS?
The 锐腾/GS was first introduced in 2015. If you have a 2013 model, it is likely a different vehicle. For any vehicle outside the 2015–2022 range, check your OE sensor number and frequency first. The BL-ST-031 is not designed for pre-2015 models.
Do I need to program this sensor before installation?
No. The BL-ST-031 is pre-programmed with a generic sensor ID that works with most compatible vehicles. You do not need to clone the original sensor ID. However, you may still need to perform a relearn procedure to sync it with your vehicle’s TPMS module.
Can I use this sensor on aftermarket wheels?
Yes, as long as the aftermarket wheels have a valve hole designed for a clamp-in sensor (standard 11.3mm or 11.5mm hole). Some aftermarket wheels require special valve stems—verify the valve hole diameter before installation.
What if my 锐腾/GS uses a different frequency (e.g., 315MHz)?
The BL-ST-031 only operates on 433MHz. If your vehicle uses 315MHz (common on some older Chinese-market vehicles), this sensor will not communicate with your TPMS receiver. Use a scan tool to confirm your frequency, or check the OE sensor for a frequency label.