Why Fitment Verification Matters for WHALE TPMS Sensors
WHALE vehicles (including the Im, MG, Rising, and Roewe sub-brands) use a mix of TPMS sensor frequencies and protocols depending on the model year and assembly plant. A sensor that looks identical may not communicate correctly with your ECU. The BL-ST-068 sensor from BH-Sens (Baolong Technology) is a pre-programmed, clamp-in unit running at 433MHz. It replaces several OE numbers, but it is not backward-compatible with older 315MHz systems or vehicles that require programmable sensors.
WHALE Model Coverage for BL-ST-068
Based on OE fitment data from Baolong and aftermarket cross-references, the BL-ST-068 covers approximately 59 WHALE-related models. Below is a high-level fitment table for the most common WHALE sub-brands.
| WHALE Sub‑Brand | Compatible Models (Examples) | Approximate Year Range | OE Numbers Covered |
|---|---|---|---|
| Im (Im) | Im5, Im6, Im8, Im EV | 2016–2023 | 10290600, 10625492 |
| MG | MG ZS, MG HS, MG5, MG6, MG RX5 | 2017–2024 | 10625492, 10718213 |
| Rising (Rising Auto) | R7, R9, ER6, Marvel R | 2020–2024 | 10718213, 11205327 |
| Roewe | Roewe i5, i6, iMAX8, RX5 Max | 2015–2023 | 10290600, 10625492 |
Important: This table is a general guide. Actual fitment depends on the exact trim, production month, and regional TPMS regulations. Always cross-check your OE sensor number before purchasing.
How to Verify Fitment Before Buying (Step-by-Step)
Step 1: Locate Your Current TPMS Sensor’s OE Number
The easiest way to confirm fitment is to find the part number printed on your current sensor. Look at the metal housing—most BH-Sens OE replacements have a 6–8 digit number like 10290600. Common locations:
- Valve stem (visible without removing the tire)
- Side of the sensor body (remove the tire or look through the wheel cavity)
- Inside the glove box or spare tire well (some vehicles have a sticker listing TPMS part numbers)
If you can’t see the number, you can also check your vehicle’s service manual or call a WHALE dealer with your VIN.
Step 2: Check Your Vehicle’s TPMS Frequency
WHALE vehicles built after 2015 almost exclusively use 433MHz sensors. However, a small number of early Roewe models (2014–2015) used 315MHz. The BL-ST-068 is 433MHz only. To verify:
- Look for a label on the sensor that says “433MHz”
- Use an aftermarket TPMS scanner tool (many shops have them)
- Check your owner’s manual under “Tire Pressure Monitoring System”
Step 3: Confirm the Valve Type
The BL-ST-068 is a clamp-in sensor—it uses a metal nut to secure it to the wheel. If your WHALE vehicle has a snap-in rubber valve stem sensor, this product will not fit. Most WHALE models from 2016 onward use clamp-in sensors, but double-check by looking at the valve stem: clamp-in sensors have a visible metal hex nut, while snap-in sensors have a rubber base.
Step 4: Use an Online Fitment Tool
Many parts retailers (including risensauto.com) offer a VIN-based fitment checker. Enter your 17-digit VIN on the product page for the BL-ST-068 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Im, MG, Rising, Roewe | OE# 10290600, 10625492, 10718213 to get a real-time compatibility result. This is the most reliable method because it accounts for mid-year changes and regional variations.
What If Your WHALE Vehicle Isn’t Listed?
If your WHALE model isn’t in the table above (e.g., older Roewe 750 or MG TF), the BL-ST-068 likely won’t work. These vehicles may use 315MHz or require a programmable sensor instead of a pre-programmed one. In that case, look for a BH-Sens sensor that matches your exact OE number or consider a universal programmable sensor.
Common Fitment Pitfalls to Avoid
- Do not assume “fits all WHALE models” – even within the same model year, different trims can use different sensors (e.g., base vs. sport suspension).
- Do not mix 433MHz and 315MHz sensors – the ECU will reject mismatched signals, causing the TPMS warning light to stay on.
- Do not reuse old mounting hardware – clamp-in sensors require new valve stems and seal kits to prevent air leaks. The BL-ST-068 usually ships with a new grommet and nut.
Recommended Part
For WHALE owners with confirmed OE numbers 10290600, 10625492, 10718213, or 11205327, the BL-ST-068 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Im, MG, Rising, Roewe | OE# 10290600, 10625492, 10718213 is a direct drop-in replacement. It comes pre-programmed, so no cloning or programming tool is needed—just install and drive a few minutes for the system to auto-learn.
FAQ
Can I install the BL-ST-068 on a 2014 WHALE Im?
No. WHALE Im models from 2014 primarily used 315MHz sensors. The BL-ST-068 is 433MHz and will not communicate with the ECU. Check your sensor’s frequency first, or upgrade to a compatible 315MHz sensor from BH-Sens.
How do I know if my WHALE vehicle uses clamp-in or snap-in sensors?
Look at the valve stem inside the wheel well. Clamp-in sensors have a visible metal hex nut where the stem meets the wheel. Snap-in sensors have a rubber base and no nut. Most WHALE vehicles from 2016 onward use clamp-in, but always verify visually.
Do I need to reprogram the BL-ST-068 after installation?
No. The BL-ST-068 is pre-programmed with the correct protocol for the OE numbers listed. After installation, drive at 15–25 mph for 5–10 minutes so the vehicle’s TPMS module can auto-learn the new sensor IDs. No tool is required.
What if my OE number isn’t listed as compatible?
The BL-ST-068 is designed specifically for OE numbers 10290600, 10625492, 10718213, and 11205327. If your sensor has a different number, it will not work. Use a parts lookup tool with your VIN to find the correct BH-Sens sensor for your WHALE model.