Overview of TPMS Relearn on the MINI JCW CLUBMAN
The MINI JCW Clubman uses a direct TPMS system (pressure sensors inside each tire). After installing new sensors—such as the BL-ST-046 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Hongqi | OE# 3778080HA01—the vehicle’s ECU must learn each sensor’s unique ID. Skipping this step means the TPMS light will stay on, and no pressure data will display.
The Clubman generally supports three relearn methods. Choose based on the tools you have and your preference for driving time.
Method 1: Auto Relearn (Drive-Only)
This is the simplest method, requiring no special tools.
- Inflate all tires to the correct pressure (check the driver’s door jamb sticker; typically 32–38 psi for this model).
- Start the engine and drive the vehicle above 15 mph (25 km/h) for 10–20 minutes.
- The system will automatically detect the new sensor IDs as you drive. The TPMS light should turn off.
- If the light stays on after 30 minutes of driving, try a different method.
Limitations: The auto relearn may fail if the sensor IDs are too different or if the vehicle was previously programmed to a different sensor brand. It works best with OE-type sensors like BH-Sens.
Method 2: OBD Relearn (Fastest)
This method uses a TPMS-capable scan tool connected to the OBD-II port. Recommended tools: Autel TS508, Foxwell NT510, or ATEQ Quickset.
- Connect the tool to the OBD-II port (under the dashboard, driver’s side).
- Navigate to TPMS > Relearn > MINI > JCW Clubman.
- Follow the tool’s prompts. It will write the sensor IDs into the ECU directly.
- Confirm the relearn is complete. The TPMS light should turn off immediately.
Tools like the Autel TS508 also allow you to trigger each sensor to verify it’s working before writing.
Method 3: Stationary Relearn (Trigger Tool Required)
For this method, you need a TPMS trigger tool (a handheld device that activates each sensor).
- Park the vehicle and turn the ignition ON (engine off).
- Use the trigger tool in the following order: LF → RF → RR → LR (driver’s side front first).
- Hold the tool against the tire sidewall near the valve stem. Press the trigger button until the horn chirps or the tool confirms.
- Repeat for each tire in order.
- After the last tire, the horn will chirp twice to confirm the relearn is complete.
Sensor Compatibility Table:
| Sensor Brand | Frequency | OE Number | Clamp Type | Compatible with MINI JCW Clubman |
|---|---|---|---|---|
| BH-Sens (Baolong) | 433MHz | 3778080HA01 | Clamp-in | Yes (pre-programmed) |
| Original MINI | 433MHz | Varies by year | Clamp-in | Yes (programming required) |
| Other aftermarket | 433MHz | Various | Clamp-in | Usually yes, check compatibility |
Recommended Part
For a reliable, no-hassle replacement, use the BL-ST-046 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Hongqi | OE# 3778080HA01. It is pre-programmed to the correct 433MHz frequency and fits the MINI JCW Clubman without additional programming for the sensor itself. Just install and perform the relearn.
FAQ
How long does a TPMS relearn take on a MINI JCW Clubman?
With OBD relearn, about 5 minutes. With auto relearn, expect 20–30 minutes of driving. Stationary relearn takes 10 minutes with a trigger tool.
Can I use sensors from other BMW models on the Clubman?
Yes, many BMW 433MHz TPMS sensors are cross-compatible, but the Clubman uses a specific ID format. Always verify the OE number or use a model-specific sensor like the BH-Sens BL-ST-046.
Why does the TPMS light stay on after new sensors?
Either the relearn was not performed, the sensor battery is dead (rare with new sensors), or the sensor is not compatible. Check the frequency (must be 433MHz) and ensure you followed the correct relearn order.
Do I need to reprogram the sensor itself before installation?
No. The BH-Sens BL-ST-046 is pre-programmed to 433MHz. The only necessary step is the vehicle relearn—adding the sensor’s ID to the ECU.