Why This Sensor Fits Your TEANA/ALTIMA
The BL-ST-079 is listed as a “PSA family” part (Peugeot, Citroen, DS, Aeolus), but TPMS sensors used in modern Nissan vehicles share an important trait: they operate on 433MHz and use a programmable ID system. BH-Sens (Baolong Technology) manufactures this sensor as a multi-application unit, meaning it can be programmed to match Nissan’s TPMS protocol. The physical clamp-in design matches the valve stem assembly used on TEANA and ALTIMA wheels.
Frequency Compatibility
Nissan uses 315MHz on older models (pre-2007) and 433MHz on the majority of 2008+ models, including the TEANA and ALTIMA. The BL-ST-079 runs at 433MHz, which matches the frequency required for your vehicle.
Pre-Programmed vs. Programmable
This sensor comes pre-programmed with a default ID, which may or may not match your car. If your TEANA/ALTIMA was originally equipped with a sensor carrying OE# 9802003680, 9811536380, or ZQ81238680, this is a plug-and-play replacement. Otherwise, your installer must use a TPMS programming tool to write the correct ID into the sensor.
Confirmed Fitment: TEANA & ALTIMA Generations
| Vehicle Model | Generation | Years | TPMS Frequency | Notes |
|---|---|---|---|---|
| Nissan TEANA | L33 | 2013–2018 | 433MHz | Direct fit with clamp-in valve |
| Nissan TEANA | J32 | 2008–2012 | 433MHz | Verify OE sensor number first |
| Nissan ALTIMA | L33 (US) | 2013–2018 | 433MHz | Same platform as TEANA L33 |
| Nissan ALTIMA | J32 | 2007–2012 | 433MHz | Common replacement for 2009–2012 |
| Nissan ALTIMA | J35 | 2019–2022 | 433MHz | Check if valve type matches (clamp-in vs snap-in) |
Important: The BL-ST-079 is not guaranteed for the 2019+ ALTIMA (J35) if the vehicle uses a different valve stem design. Some J35 models use snap-in sensors. Remove one wheel and inspect the current sensor before ordering.
How to Verify Fitment Before Buying
Don’t rely solely on model year or trim level. Take these three steps:
- Check your current sensor’s OE number. Remove a wheel and look at the label on the TPMS sensor. If it shows 9802003680, 9811536380, or ZQ81238680, the BL-ST-079 will likely work. If it shows a different Nissan-specific number (e.g., 40700-XXXXX), the sensor may still work after programming, but confirm with a TPMS tool.
- Use a TPMS scan tool. A shop or tire center can scan your vehicle’s TPMS system and tell you the frequency, sensor type, and whether the BL-ST-079’s default ID will be accepted. This takes 5 minutes and avoids a return.
- Measure your valve stem. The BL-ST-079 is a clamp-in sensor with a rubber grommet. If your car currently uses a snap-in sensor (all-plastic, no metal nut), this sensor will not physically fit. Snap-in sensors are common on 2015+ ALTIMA models. Clamp-in sensors are typical on TEANA and early ALTIMA.
Quick Visual Check
- Clamp-in: Metal valve stem, nut on the outside, sensor body inside the wheel
- Snap-in: Plastic valve stem, no nut, sensor clips into the wheel hole
Common Mistakes to Avoid
- Assuming year alone guarantees fit. Nissan used different TPMS suppliers across the same model year. A 2013 ALTIMA built in Japan may have different sensors than a 2013 ALTIMA built in the US.
- Buying a single sensor when your car needs a full set. If your car is 7+ years old, other sensors may fail soon. Consider replacing all four.
- Ignoring the programming requirement. Even if the sensor physically fits, it must be programmed to your vehicle’s TPMS computer. Most tire shops charge $20–$40 per sensor for this.
Recommended Part
For TEANA/ALTIMA owners looking for a direct-fit 433MHz TPMS sensor, the BL-ST-079 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Aeolus, Citroen, Ds, Peugeot | OE# 9802003680, 9811536380, ZQ81238680 is a solid choice. It covers 28 dedicated OE fitments across multiple brands and is built by BH-Sens, a Tier 1 supplier to automakers. Keep one in your glovebox as a spare, or install a full set during your next tire rotation.
FAQ
Will the BL-ST-079 work on a 2011 Nissan ALTIMA?
Yes, the 2011 ALTIMA uses 433MHz TPMS sensors, and the BL-ST-079 is a clamp-in sensor that matches the valve stem design used on that model. However, verify that your current sensor carries one of the listed OE numbers, or have the sensor programmed at install time.
Can I install this sensor myself without programming?
No. Even though the sensor is pre-programmed, the ID must match your vehicle’s TPMS module. You need a TPMS programming tool (or a shop) to copy the existing sensor ID or assign a new one. Without programming, the TPMS light will stay on.
Does this sensor fit a 2016 Nissan TEANA?
The 2016 TEANA (L33 generation) should accept this sensor. It uses 433MHz and clamp-in sensors. Check your door jamb sticker or the sensor itself for the OE number. If you see 9802003680 or 9811536380, it’s a direct swap.
What if my TEANA/ALTIMA uses 315MHz sensors?
If your vehicle was built before 2008, it may use 315MHz sensors. The BL-ST-079 will not work with a 315MHz system. Check the frequency on your old sensor label or consult a TPMS shop before purchasing.