Geelygalaxy TPMS Sensor Fitment Guide: How to Verify Compatibility Before You Buy

Understanding TPMS Sensor Fitment for Geelygalaxy Vehicles

If you’re replacing a dead or damaged TPMS sensor on your Geelygalaxy, the last thing you want is to receive a part that doesn’t fit. The BL-ST-050 is a clamp-in, pre-programmed TPMS sensor designed specifically for Geelygalaxy, Lynk&Co, and Zeekr models. But not every sensor works on every year or trim. Here’s how to nail the fitment the first time.

The sensor operates at 433MHz, which is the standard frequency for most Geelygalaxy TPMS systems. It replaces OE parts 6608082005 and 8894215959. That’s your starting point.

Which Geelygalaxy Models Does the BL-ST-050 Fit?

The BL-ST-050 covers at least 13 dedicated OE fitments across the Geelygalaxy lineup. Based on factory data and real-world installations, here are the confirmed compatible models:

Note: This table is based on industry-verified data. If your Geelygalaxy model isn’t listed, check the OE number on your original sensor. If it reads 6608082005 or 8894215959, the BL-ST-050 is your match.

How to Verify Fitment Before You Buy

Don’t rely solely on model names. Follow these steps to confirm compatibility:

Step 1: Locate Your Current TPMS Sensor Part Number

Remove the tire (or look through the valve stem area) to read the number stamped on the sensor. Common locations:

• Inside the tire, attached to the valve stem
• On the sensor body itself (silver or black plastic housing)

For Geelygalaxy, the OE number is usually 6608082005 or 8894215959. If you see either, you’re good.

Step 2: Check Your Vehicle’s TPMS Frequency

Geelygalaxy switched from 315MHz to 433MHz around 2018–2020 depending on the model. To confirm:

• Look at your original sensor: it should say “433MHz” or “433.92MHz” on the label.
• Check your owner’s manual under “Tire Pressure Monitoring System” specifications.
• Use an OBD2 scanner to read the TPMS module frequency (advanced).

Step 3: Confirm Valve Stem Type

The BL-ST-050 is a clamp-in sensor. If your Geelygalaxy uses a snap-in sensor (rare on these models), you’ll need a different part. Clamp-in sensors have a metal nut securing them to the wheel; snap-in sensors use a rubber grommet. Look at your current sensor—if it’s metal threaded, clamp-in is correct.

Step 4: Use an Online Fitment Checker

On risensauto.com, enter your Geelygalaxy year, model, and trim into the product page for BL-ST-050 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Geelygalaxy, Lynk&Co, Zeekr | OE# 6608082005, 8894215959. The system cross-references OE numbers and vehicle databases to guarantee a match.

Compatibility Beyond Geelygalaxy: Lynk&Co and Zeekr

The BL-ST-050 isn’t limited to Geelygalaxy. It also fits:

• Lynk&Co 01, 02, 03, 05, 06, 09 (2018–2025)
• Zeekr 001, 009 (2021–2025)

These brands share the same TPMS platform under the Geely Holding Group. If you own a Lynk&Co or Zeekr and need a replacement sensor, the same verification steps apply—check the OE number and frequency.

Pre-Programmed vs. Programmable: Why It Matters

The BL-ST-050 is pre-programmed. That means it comes ready to install with the correct protocols for Geelygalaxy, Lynk&Co, and Zeekr. You don’t need a TPMS tool to program the sensor ID before installation.

What you still need to do:

• Install the sensor in the wheel.
• Mount and balance the tire.
• Relearn the sensor IDs to your vehicle’s TPMS module.

Relearning can be done via:

• A TPMS reset tool (like Autel or Bartec)
• Driving at 15–20 mph for 10–15 minutes (some models auto-relearn)
• Dealer-level diagnostics

For Geelygalaxy models after 2021, the relearn procedure usually involves a scan tool. Check your manual for the specific sequence.

Common Fitment Mistakes to Avoid

• Assuming all 433MHz sensors are identical. They’re not. The BL-ST-050 uses Baolong Technology’s proprietary protocol. A generic 433MHz sensor from another brand may not communicate with your Geelygalaxy ECU.
• Ignoring the year cutoff. If you own a 2017 Geelygalaxy, it may use 315MHz. Always verify frequency before ordering.
• Mixing clamp-in and snap-in. Clamp-in sensors require a metal nut and washer; snap-in sensors are push-fit. The BL-ST-050 is clamp-in only.

Recommended Part

For a direct replacement that matches your Geelygalaxy’s factory TPMS system, use BL-ST-050 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Geelygalaxy, Lynk&Co, Zeekr | OE# 6608082005, 8894215959. It’s built by BH-Sens (Baolong Technology), the same supplier used by many OEMs in China. The sensor is pre-programmed for Geelygalaxy, Lynk&Co, and Zeekr, and covers over a dozen OE fitments with zero additional programming steps.

FAQ

How do I know if my Geelygalaxy uses 433MHz or 315MHz TPMS sensors?

Check the label on your current sensor. If it says “433MHz” or “433.92MHz,” that’s your frequency. If you can’t remove the wheel, check your owner’s manual under “Tire Pressure Monitoring” or contact a dealer with your VIN. Most Geelygalaxy models from 2018 onward use 433MHz.

Can I install the BL-ST-050 sensor myself?

Yes, if you have the tools to remove the tire and access the valve stem. You’ll need a tire machine to demount the tire, a torque wrench (tighten the clamp-in nut to 35–45 in-lb per spec), and a TPMS relearn tool to sync the sensor with your vehicle. If you’re not comfortable, any tire shop can install it in under 30 minutes.

Will this sensor work on a Lynk&Co 03+ (2022)?

Yes. The BL-ST-050 is confirmed compatible with Lynk&Co 03 and 03+ models from 2019 onward, as long as the original sensor uses OE number 6608082005 or 8894215959. Verify the frequency and clamp-in type before ordering.

What is the warranty on the BL-ST-050 sensor?

The sensor comes with a standard 1-year warranty from risensauto.com against manufacturing defects. BH-Sens (Baolong Technology) is a Tier-1 supplier, so failure rates are low—typically under 0.5% in the first 12 months.