Mhero TPMS Compatibility: What You Need to Know
{MHERO_BRAND_LINK} vehicles are known for their robust off-road capabilities, but like any modern car, they rely on Tire Pressure Monitoring System (TPMS) sensors to keep you safe. The BH-Sens BL-ST-063 sensor (433MHz) is a pre-programmed, clamp-in unit that directly replaces the factory sensors on many Mhero models. It’s manufactured by Baolong Technology, the same OE supplier used by several Chinese automakers.
Which Mhero Models Use the BL-ST-063 Sensor?
The BL-ST-063 is designed to fit Mhero models produced between 2021 and the present. The sensor is shared across a family of brands under the same parent group. The table below lists the compatible brands and typical year ranges (always confirm using your VIN or OE number):
| Brand | Compatible Models (Examples) | Typical Year Range |
|---|---|---|
| Mhero | 917, 718, etc. | 2021 – 2025 |
| Aeolus | Many passenger models | 2021 – 2025 |
| Eπ | SUV and sedan lineup | 2021 – 2025 |
| Nammi | Electric urban vehicles | 2022 – 2025 |
| Voyah | Free, Dreamer, Passion | 2022 – 2025 |
Note: Year ranges are approximate. Some early or late production runs may differ – always cross-reference with your original sensor’s part number.
How to Verify Fitment Before Buying
Don’t rely solely on the model name or year. Follow these three steps to ensure the BL-ST-063 will work on your Mhero:
- Locate your OE sensor part number – Remove the valve cap and look for a stamped number on the sensor body. Common Mhero OE numbers for this sensor are E300019160, E300020260, and H56A7920001AC. If your sensor has one of these, the BL-ST-063 is a direct swap.
- Check the frequency – Mhero uses 433MHz TPMS. If you have an aftermarket system that runs on 315MHz, this sensor won’t work. The BL-ST-063 is factory-programmed to 433MHz.
- Verify the sensor type – This is a clamp-in sensor (metal valve stem retained by a nut). If your vehicle uses a snap-in rubber stem sensor, you’ll need a different part. Mhero models from 2021 onward use clamp-in sensors.
Still unsure? Contact our support team with your VIN – we can match it to the correct sensor in seconds.
Recommended Part
For a hassle-free replacement, we recommend the BL-ST-063 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Aeolus, Eπ, Mhero, Nammi, Voyah | OE# E300019160, E300020260, H56A7920001AC – it’s pre-programmed, plug-and-play, and covers the most common Mhero applications. One sensor fits all four positions.
FAQ
Will this sensor work on a 2023 Mhero 917?
Yes, the BL-ST-063 is confirmed compatible with the 2023 Mhero 917, provided your original sensor is one of the OE numbers listed above. If your vehicle was built early in the 2023 model year, double-check the part number on your existing sensor.
How do I find the OE number on my current TPMS sensor?
Remove the tire, locate the sensor attached to the valve stem. The OE number is usually laser-etched or printed on the metal body. You may need a flashlight. Common locations: on the sensor cap or just below the valve stem base. Wear numbers are not the OE number – look for a 9- to 12-digit code.
Is the BL-ST-063 pre-programmed, or does it need cloning?
It is pre-programmed from the factory to work with Mhero and other listed brands. No cloning or additional programming is required. However, after installation, your vehicle may need a TPMS relearn procedure – consult your owner’s manual for the specific reset method (usually a button sequence or driving at 15 mph for 5 minutes).
What if my Mhero uses a different sensor frequency?
All Mhero models sold since 2021 use 433MHz. If you are unsure, check the label on your old sensor – it will specify “433MHz” or “433.92MHz.” If you find a different frequency, do not buy this sensor; look for a 315MHz version instead.