Understanding Jetour TPMS Sensor Compatibility
{Jetour_link} is a relatively young brand under Chery’s umbrella, and its TPMS systems follow Chery’s electronics architecture. The BL-ST-075 sensor from BH-Sens (Baolong Technology) is engineered to match this ecosystem. It operates at 433MHz — the standard frequency for Asian-market Jetour vehicles — and uses a clamp-in design, which is the factory fitment for steel and aluminum rims on Jetour models from 2018 onward.
The sensor is pre-programmed, meaning it comes ready to pair with your Jetour’s ECU. No cloning or additional programming tool is needed if your vehicle originally used a Baolong TPMS sensor. However, always verify the specific year and trim, as some early Jetour models (2017–2018) may use a different protocol.
Jetour Models Covered by BL-ST-075
The BL-ST-075 covers most Jetour models produced after 2018. Below is the confirmed compatibility data. For models not listed, check your OE sensor number.
| Jetour Model | Model Years Covered | Notes |
|---|---|---|
| X70 / X70S | 2018–2024 | All trims. Pre-2020 models may need sensor relearn. |
| X90 / X90 Plus | 2019–2024 | Compatible with both 17″ and 18″ factory wheels. |
| Dashing (Dasheng) | 2021–2024 | Uses same OE reference F023114011. |
| X95 | 2020–2022 | Verify with OE number before ordering. |
| Traveler (Lvxing Zhe) | 2023–2024 | Confirmed fit, but double-check valve stem length. |
Important: The BL-ST-075 also fits other Chery Group brands — Chery, Cowin, Karry, Soueast — which share the same TPMS platform.
How to Verify Fitment Before Buying
Follow these three steps. They take five minutes and prevent returns.
Step 1: Locate Your Current Sensor’s OE Number
Remove the tire and read the number printed on the metal body of your existing TPMS sensor. Common Jetour OE numbers for this sensor are:
- F023114011
- F113114011
- F113114011BA
If your sensor shows any of these, the BL-ST-075 is a direct swap.
Step 2: Confirm the Frequency (433MHz vs. 315MHz)
Jetour vehicles sold in China, Southeast Asia, and the Middle East use 433MHz. If you have a Jetour exported to North America or a grey-market import, check the frequency printed on the old sensor. The BL-ST-075 is 433MHz only. Do not use it if your vehicle requires 315MHz.
Step 3: Check Valve Type and Rim Fitment
The BL-ST-075 is a clamp-in sensor with a metal valve stem. It fits standard 11.5mm valve holes found on factory Jetour wheels. If your aftermarket wheels have aftermarket TPMS holes or different valve designs, measure the hole diameter. Clamp-in sensors will not work with snap-in rubber stems.
Installation and Relearn Procedure
Installation is straightforward if you are swapping a dead sensor:
- Mount the sensor with a new seal kit (included with BL-ST-075 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Chery, Cowin, Jetour, Karry, Soueast | OE# F023114011, F113114011, F113114011BA). Torque the retaining nut to 4–5 Nm — over-tightening can crack the sensor body.
- Balance the wheel after installation.
- Relearn the sensor to your Jetour. The procedure varies by model year:
- 2018–2020 models: Use a TPMS trigger tool to wake the sensor, then drive above 25 km/h for 5 minutes. The system auto-learns.
- 2021–2024 models: Enter the TPMS relearn mode via the infotainment menu (Settings > Vehicle > TPMS > Relearn). Follow on-screen prompts.
If the sensor does not register, confirm the sensor is within 1 meter of the receiver module (located behind the glove box or near the rear wheel well on most Jetour models).
When NOT to Use the BL-ST-075
- Your Jetour uses 315MHz sensors (rare, but check).
- Your factory sensor is snap-in type (the BL-ST-075 is clamp-in only).
- Your vehicle is a 2017 or earlier Jetour — these sometimes use a different protocol not supported by this sensor.
Recommended Part
For a drop-in replacement that covers the vast majority of Jetour models from 2018 onward, use BL-ST-075 | BH-Sens 433MHz TPMS Tire Pressure Sensor | Fits Chery, Cowin, Jetour, Karry, Soueast | OE# F023114011, F113114011, F113114011BA. It is pre-programmed and requires no additional tools for standard pairing. Always verify your OE number before purchase.
FAQ
Does the BL-ST-075 work with Jetour X70 from 2022?
Yes. The 2022 Jetour X70 uses OE number F113114011BA, which matches the BL-ST-075. It is a direct fit. Relearn via the infotainment menu after installation.
Can I install this sensor myself without a TPMS tool?
You can install it physically (mount and torque), but you will need a TPMS trigger tool or a professional scan tool to wake the sensor for pairing. Some 2021+ Jetour models can auto-learn after driving, but a trigger tool is recommended for reliable results.
What is the difference between F023114011 and F113114011BA?
Both are Baolong-manufactured sensors for the Chery/Jetour family. The F113114011BA is a later revision with slightly improved battery life. The BL-ST-075 replaces both. There is no functional difference for fitment or programming.
My Jetour Dashing shows a TPMS light after tire rotation. Do I need new sensors?
Not necessarily. Tire rotation on Jetour Dashing does not require sensor replacement. The vehicle automatically recognizes sensor positions after driving 5–10 minutes above 30 km/h. If the light stays on, check battery charge on each sensor using a TPMS diagnostic tool. The BL-ST-075 can replace any dead sensor in the set.